一、????產品簡介
product introduction
執行標準：GB25202-2010
?Execution standard: GB25202-2010
空氣泡沫槍是一種能產生和噴射空氣泡沫，用以撲救中型油類火災的比較輕便的消防器材。
foam fire branchis a kind of can produce and injection air bubble to save the comparison of the medium oil fire light fire equipment.
空氣泡沫槍由噴嘴、啟閉柄、手輪，槍筒、吸液管、密封圈、吸液管接頭、槍體、管牙接口等組成。噴嘴是用以控制流量和產生負壓，啟閉柄是空氣泡沫槍液流開關和吸液開關，手輪用來控制泡沫槍噴射方向，槍筒用以調節空氣泡沫膨化的動態平衡，吸液管用以吸取泡沫液，密封圈用以密封，吸液管接頭用以的吸液管連接，槍體是空氣泡沫槍的支座，管牙接口用以與消防水帶連接。
foam fire branch?by spray nozzle, handles, opening and closing the handwheel, barrel, absorb fluid pipe, sealing ring, to absorb fluid tube fittings, of gun, tube tooth interface etc.?The nozzle to control the flow and is produced negative pressure, open the handle is air foam gun liquid flow switch and absorb fluid switch, the handwheel is used to control the foam spray gun direction, barrel to adjust air bubble expanded the dynamic balance, absorb fluid work to absorb liquid foam, sealing ring to seal, absorb fluid pipe joint to absorb fluid of tube connects, of gun is? foam fire branch bearing, the tooth interface to the fire hose connection with.
二、????工作原理
work principle
空氣泡沫槍進水口端與消防水帶連接，吸液管接口與吸液連接，吸液管另一端插入泡沫液桶內，當水流以0.7MPa壓力通過水帶進入槍內，經噴嘴噴出時，槍體內在水流的作用下形成負壓，此時泡沫液通過吸液管吸入槍體內與水混合，當混合液由噴嘴射出時，由于射速再次形成負壓，吸入大量空氣與混合液混合，當經過槍筒使空氣泡沫混合膨化，空氣泡沫達到平衡后由槍筒噴出。
foam fire branch inlet end and the fire hose connection, to absorb fluid pipe interface and absorb fluid connection, to absorb fluid pipe the other end into the liquid foam inside bucket, with 0.7 MPa pressure when water flow through the water into the gun within the nozzle jet, the gun in the role of water in the body formed under negative pressure, the liquid foam at this time by smoking gun body in liquid pipe is mixed with water, and when the mixture by injection nozzle, because again firing rate forming negative pressure, and a lot of air inhaled with the mixture mixing, when after air bubble mixing barrel expanded, and the air bubble to balance out the barrel.
三、????用戶須知
user guidelines
1、??????????空氣泡沫槍應配用3%-6%的泡沫液
2、??????????噴射時，應使泡沫向順風方向噴射，避免測風和逆風噴射
3、??????????在不采用吸液管吸取泡沫時，消防水泵上需配備泡沫比例混合器，以便按規定比例輸送泡沫混合液
4、??????????空氣泡沫槍的工作壓力是指泡沫槍進水口端的水流壓力
5、??????????空氣泡沫槍必須經常檢查并保持槍體、手輪、槍筒、噴嘴、管牙接口、密封件的完整好用
6、??????????盡量避免磕碰摔打，以免損壞或影響使用，造成不必要的損失
7、??????????使用完畢，要將各部位清洗干凈，置于陰涼干燥的地方妥善保管
8、??????????平時不得與酸堿等化學物質混放，遠離熱源，以防各橡膠部件和高壓聚乙稀件老化變形
9、??????????運輸的貯存中均應避免重壓、撞擊、雨淋、曝曬和接觸腐蝕性化學物質
10、???????產品保質期1年，因安裝或使用不當等引起和質量問題或經濟損失，不屬于本公司責任范圍
1,?foam fire branch should be 6% of the bubble with liquid
2, injection, should make foam injection to a direction, avoid the wind and against the wind injection
3, in not using liquid pipe absorption from bubble, fire pump on the need to have foam proportion mixer, so as to press formulary scale conveying foam mixture
4, foam fire branch pressure of work is to point to the inlet water bubble gun pressure
5, foam fire branch must often check and maintain of gun, the handwheel, barrel, nozzle, tube and sealing pieces of complete tooth interface works better
6, try to avoid knock against throw, lest damage or affected use, cause needless loss
7, after use, to the place clean, in a cool, dry place for safe keeping
8, at ordinary times may not soda acid and chemical readjusting, far away from heat, in case the rubber components and high pressure polythene pieces together the aging deformation
9, the storage of the transport shall avoid stress, bump, rain, and contact corrosive chemical exposure
10, product the expiration period 1 year, because of installation or improper use of the causes and quality problem or economic loss, do not belong to the company responsibilities